Profile Section

260x96x2.5mm S350GD+Z Galvanized Steel C Plus Profile

The 260x96x2.5mm steel C Plus profile is a cold roll-formed double-lipped channel to EN 10162 with a 260 mm web, 96 mm flanges, fixed 25+15 mm double edge lips and 2.5 mm sheet thickness, weighing a nominal 10.44 kg/m. Produced to order in galvanized S350GD+Z steel, the C+ geometry carries higher loads than a standard C of similar weight — used as heavy purlins, columns and beams in industrial and light steel buildings. This variant is pre-galvanized structural strip S350GD+Z275 to EN 10346, minimum yield about 350 MPa. The zinc coating is already on the coil, which is why this is the standard grade for outdoor purlins and solar structures.

Select Size

Select Grade

Made to Order — Roll Formed

This profile is roll-formed to order in your exact length (1–15 m; longer on project basis). Minimum production run is approx. 3000 kg per size and grade. Add your sizes to a quote request and our team confirms lead time and pricing within one business day.

Add to Quote Request

Select length and quantity to add to your quote cart

Select Length

Quantity (pieces)

Minimum order: 24 pieces

Minimum total length: 288 m

Weight per meter:10.44 kg/m

Total length:12 meters

Total weight:125.28 kg

Production options

Optional made-to-order requirements — added to this line for our production team.

Coating weight

Pre-painted finish (RAL)Punching / holes to drawingMill certificate EN 10204 3.1

Send your list Contact sales

Applications & Usage

C+ 260x96x2.5 is typically specified for load-bearing purlins, stringcourses and facade rails on heavy industrial buildings, and as columns, beams and roof trusses in warehouses, hangars and light-gauge steel frames. Mounting holes are punched in-line to your drawing; the double-lip section pairs with bolted cleats for fast assembly. S350GD+Z275 is the usual specification for solar mounting, roof and wall purlins, and any outdoor structure that needs a structural yield plus a zinc coating from the mill. At a nominal 10.44 kg/m and cut-to-length production from 1 to 15 m, material usage is optimized with no offcuts on site. Minimum production run is approximately 3000 kg per size and grade — add your sizes to a quote request and our team confirms exact tonnage, lead time and delivered pricing.

Technical Specifications

Specification	Value
Dimensions	260mm × 96mm × 2.5mm
Weight per Meter	10.44 kg/m
Material	Steel
Alloy/Grade	S350GD+Z275
Standard	EN 10162 / EN 10346
Profile Type	C Plus (double-lip C+)
Edge Lip (c)	25+15 mm
Developed Width	≈ 532 mm
Cross-Section Area	≈ 13.30 cm²
Moment of Inertia Iₓ	≈ 1433.3 cm⁴
Moment of Inertia Iᵧ	≈ 190.9 cm⁴
Section Modulus Wₑₗ,ₓ	≈ 109.20 cm³
Section Modulus Wₑₗ,ᵧ	≈ 28.97 cm³
Minimum Production Run	3 t
Finish	S350GD+Z Galvanized
Available Lengths	6m, 12m
Standard Length	6 m
Minimum Order Length	288 m
Cut-to-Length Range	1000 – 15000 mm

Indicative elastic section properties computed from the nominal centerline (thin-walled, corner radii ignored). For preliminary sizing only — not a substitute for a stamped structural calculation.

Indicative load span (single span, simply supported)

Allowable uniformly-distributed load (kN/m) limited by elastic bending about the strong axis (γ = 1.5 on yield, S350GD+Z275). Deflection is not checked and usually governs long spans. Indicative only — confirm with a project calculation.