Profile Section
180x91x2.5mm S355JR Uncoated Steel C Plus Profile
The 180x91x2.5mm steel C Plus profile is a cold roll-formed double-lipped channel to EN 10162 with a 180 mm web, 91 mm flanges, fixed 25+15 mm double edge lips and 2.5 mm sheet thickness, weighing a nominal 8.67 kg/m. Produced to order in uncoated S355JR steel, the C+ geometry carries higher loads than a standard C of similar weight — used as heavy purlins, columns and beams in industrial and light steel buildings. This variant is uncoated cold-rolled structural strip in grade S355JR (EN 10025), minimum yield about 355 MPa. Choose it when the same section has to carry more load than S235JR. The surface is bare — specify paint or hot-dip galvanizing in the quote for outdoor use.
Made to Order — Roll Formed
This profile is roll-formed to order in your exact length (1–15 m; longer on project basis). Minimum production run is approx. 3000 kg per size and grade. Add your sizes to a quote request and our team confirms lead time and pricing within one business day.
Add to Quote Request
Select length and quantity to add to your quote cart
Minimum order: 29 pieces
Minimum total length: 348 m
Optional made-to-order requirements — added to this line for our production team.
Applications & Usage
C+ 180x91x2.5 is typically specified for load-bearing purlins, stringcourses and facade rails on heavy industrial buildings, and as columns, beams and roof trusses in warehouses, hangars and light-gauge steel frames. Mounting holes are punched in-line to your drawing; the double-lip section pairs with bolted cleats for fast assembly. S355JR is the higher-strength uncoated grade for load-bearing purlins, columns and frames where S235JR would need a heavier section. At a nominal 8.67 kg/m and cut-to-length production from 1 to 15 m, material usage is optimized with no offcuts on site. Minimum production run is approximately 3000 kg per size and grade — add your sizes to a quote request and our team confirms exact tonnage, lead time and delivered pricing.
Technical Specifications
| Specification | Value |
|---|---|
| Dimensions | 180mm × 91mm × 2.5mm |
| Weight per Meter | 8.674 kg/m |
| Material | Steel |
| Alloy/Grade | S355JR |
| Standard | EN 10162 / EN 10346 |
| Profile Type | C Plus (double-lip C+) |
| Edge Lip (c) | 25+15 mm |
| Developed Width | ≈ 442 mm |
| Cross-Section Area | ≈ 11.05 cm² |
| Moment of Inertia Iₓ | ≈ 597.5 cm⁴ |
| Moment of Inertia Iᵧ | ≈ 148.5 cm⁴ |
| Section Modulus Wₑₗ,ₓ | ≈ 65.48 cm³ |
| Section Modulus Wₑₗ,ᵧ | ≈ 25.80 cm³ |
| Minimum Production Run | 3 t |
| Finish | S355JR Uncoated |
| Available Lengths | 6m, 12m |
| Standard Length | 6 m |
| Minimum Order Length | 348 m |
| Cut-to-Length Range | 1000 – 15000 mm |
Indicative elastic section properties computed from the nominal centerline (thin-walled, corner radii ignored). For preliminary sizing only — not a substitute for a stamped structural calculation.
Indicative load span (single span, simply supported)
Allowable uniformly-distributed load (kN/m) limited by elastic bending about the strong axis (γ = 1.5 on yield, S355JR). Deflection is not checked and usually governs long spans. Indicative only — confirm with a project calculation.
| Span | Max UDL |
|---|---|
| 2 m | ≈ 30.99 kN/m |
| 3 m | ≈ 13.77 kN/m |
| 4 m | ≈ 7.75 kN/m |
| 5 m | ≈ 4.96 kN/m |
| 6 m | ≈ 3.44 kN/m |
Made to Order — Roll Formed
This profile is roll-formed to order in your exact length (1–15 m; longer on project basis). Minimum production run is approx. 3000 kg per size and grade. Add your sizes to a quote request and our team confirms lead time and pricing within one business day.
Cut to exact length
Any length from 1 to 15 m — no offcut waste on site
Material options
Uncoated S355JR high-strength cold-rolled strip. Paint or hot-dip galvanize after forming when corrosion protection is required.
In-line punching
Mounting holes and slots punched to your drawing during roll forming
Certified quality
Produced to EN 10162; EN 10204 3.1 mill certificates available
Similar Sizes
Explore alternative dimensions that might suit your needs