Profile Section
100x92x1.2mm S235JR Uncoated Steel C Plus Profile
The 100x92x1.2mm steel C Plus profile is a cold roll-formed double-lipped channel to EN 10162 with a 100 mm web, 92 mm flanges, fixed 25+15 mm double edge lips and 1.2 mm sheet thickness, weighing a nominal 3.43 kg/m. Produced to order in uncoated S235JR steel, the C+ geometry carries higher loads than a standard C of similar weight — used as heavy purlins, columns and beams in industrial and light steel buildings. This variant is uncoated cold-rolled structural strip in grade S235JR (EN 10025), minimum yield about 235 MPa. The surface is bare — specify shop painting or hot-dip galvanizing in the quote when the profile will be used outdoors.
Made to Order — Roll Formed
This profile is roll-formed to order in your exact length (1–15 m; longer on project basis). Minimum production run is approx. 3000 kg per size and grade. Add your sizes to a quote request and our team confirms lead time and pricing within one business day.
Add to Quote Request
Select length and quantity to add to your quote cart
Minimum order: 73 pieces
Minimum total length: 876 m
Optional made-to-order requirements — added to this line for our production team.
Applications & Usage
C+ 100x92x1.2 is typically specified for load-bearing purlins, stringcourses and facade rails on heavy industrial buildings, and as columns, beams and roof trusses in warehouses, hangars and light-gauge steel frames. Mounting holes are punched in-line to your drawing; the double-lip section pairs with bolted cleats for fast assembly. S235JR is the general structural grade for indoor frames, painted purlins, and profiles that will be hot-dip galvanized after roll forming. At a nominal 3.43 kg/m and cut-to-length production from 1 to 15 m, material usage is optimized with no offcuts on site. Minimum production run is approximately 3000 kg per size and grade — add your sizes to a quote request and our team confirms exact tonnage, lead time and delivered pricing.
Technical Specifications
| Specification | Value |
|---|---|
| Dimensions | 100mm × 92mm × 1.2mm |
| Weight per Meter | 3.429 kg/m |
| Material | Steel |
| Alloy/Grade | S235JR |
| Standard | EN 10162 / EN 10346 |
| Profile Type | C Plus (double-lip C+) |
| Edge Lip (c) | 25+15 mm |
| Developed Width | ≈ 364 mm |
| Cross-Section Area | ≈ 4.37 cm² |
| Moment of Inertia Iₓ | ≈ 76.2 cm⁴ |
| Moment of Inertia Iᵧ | ≈ 58.6 cm⁴ |
| Section Modulus Wₑₗ,ₓ | ≈ 15.06 cm³ |
| Section Modulus Wₑₗ,ᵧ | ≈ 11.79 cm³ |
| Minimum Production Run | 3 t |
| Finish | S235JR Uncoated |
| Available Lengths | 6m, 12m |
| Standard Length | 6 m |
| Minimum Order Length | 876 m |
| Cut-to-Length Range | 1000 – 15000 mm |
Indicative elastic section properties computed from the nominal centerline (thin-walled, corner radii ignored). For preliminary sizing only — not a substitute for a stamped structural calculation.
Indicative load span (single span, simply supported)
Allowable uniformly-distributed load (kN/m) limited by elastic bending about the strong axis (γ = 1.5 on yield, S235JR). Deflection is not checked and usually governs long spans. Indicative only — confirm with a project calculation.
| Span | Max UDL |
|---|---|
| 2 m | ≈ 4.72 kN/m |
| 3 m | ≈ 2.10 kN/m |
| 4 m | ≈ 1.18 kN/m |
| 5 m | ≈ 0.75 kN/m |
| 6 m | ≈ 0.52 kN/m |
Made to Order — Roll Formed
This profile is roll-formed to order in your exact length (1–15 m; longer on project basis). Minimum production run is approx. 3000 kg per size and grade. Add your sizes to a quote request and our team confirms lead time and pricing within one business day.
Cut to exact length
Any length from 1 to 15 m — no offcut waste on site
Material options
Uncoated S235JR cold-rolled structural strip. Paint or hot-dip galvanize after forming when corrosion protection is required.
In-line punching
Mounting holes and slots punched to your drawing during roll forming
Certified quality
Produced to EN 10162; EN 10204 3.1 mill certificates available
Similar Sizes
Explore alternative dimensions that might suit your needs