Profile Section
250x80x2.5mm S355JR Uncoated Steel Z Profile
The 250x80x2.5mm steel Z profile is a cold roll-formed purlin section to EN 10162 with a 250 mm web, opposed 80 mm flanges with 25 mm edge lips and 2.5 mm sheet thickness, weighing a nominal 9.03 kg/m. Produced to order in uncoated S355JR steel, the Z geometry nests and overlaps at supports, forming structurally continuous roof and wall purlin lines that carry more load with less steel. This variant is uncoated cold-rolled structural strip in grade S355JR (EN 10025), minimum yield about 355 MPa. Choose it when the same section has to carry more load than S235JR. The surface is bare — specify paint or hot-dip galvanizing in the quote for outdoor use.
Made to Order — Roll Formed
This profile is roll-formed to order in your exact length (1–15 m; longer on project basis). Minimum production run is approx. 3000 kg per size and grade. Add your sizes to a quote request and our team confirms lead time and pricing within one business day.
Add to Quote Request
Select length and quantity to add to your quote cart
Minimum order: 28 pieces
Minimum total length: 336 m
Optional made-to-order requirements — added to this line for our production team.
Applications & Usage
Z 250x80x2.5 carries roof and wall cladding on industrial halls, warehouses, agricultural buildings and solar carports; overlapped and bolted at supports it forms continuous multi-span purlin lines. Cleat and overlap holes are punched in-line to your purlin schedule, and anti-sag accessories are configured per project. S355JR is the higher-strength uncoated grade for load-bearing purlins, columns and frames where S235JR would need a heavier section. At a nominal 9.03 kg/m and cut-to-length production from 1 to 15 m, material usage is optimized with no offcuts on site. Minimum production run is approximately 3000 kg per size and grade — add your sizes to a quote request and our team confirms exact tonnage, lead time and delivered pricing.
Technical Specifications
| Specification | Value |
|---|---|
| Dimensions | 250mm × 80mm × 2.5mm |
| Weight per Meter | 9.027 kg/m |
| Material | Steel |
| Alloy/Grade | S355JR |
| Standard | EN 10162 / EN 10346 |
| Profile Type | Z (purlin) |
| Edge Lip (c) | 25 mm |
| Developed Width | ≈ 460 mm |
| Cross-Section Area | ≈ 11.50 cm² |
| Moment of Inertia Iₓ | ≈ 1109.4 cm⁴ |
| Moment of Inertia Iᵧ | ≈ 165.3 cm⁴ |
| Section Modulus Wₑₗ,ₓ | ≈ 87.87 cm³ |
| Section Modulus Wₑₗ,ᵧ | ≈ 20.35 cm³ |
| Minimum Production Run | 3 t |
| Finish | S355JR Uncoated |
| Available Lengths | 6m, 12m |
| Standard Length | 6 m |
| Minimum Order Length | 336 m |
| Cut-to-Length Range | 1000 – 15000 mm |
Indicative elastic section properties computed from the nominal centerline (thin-walled, corner radii ignored). For preliminary sizing only — not a substitute for a stamped structural calculation.
Indicative load span (single span, simply supported)
Allowable uniformly-distributed load (kN/m) limited by elastic bending about the strong axis (γ = 1.5 on yield, S355JR). Deflection is not checked and usually governs long spans. Indicative only — confirm with a project calculation.
| Span | Max UDL |
|---|---|
| 2 m | ≈ 41.59 kN/m |
| 3 m | ≈ 18.49 kN/m |
| 4 m | ≈ 10.40 kN/m |
| 5 m | ≈ 6.65 kN/m |
| 6 m | ≈ 4.62 kN/m |
Made to Order — Roll Formed
This profile is roll-formed to order in your exact length (1–15 m; longer on project basis). Minimum production run is approx. 3000 kg per size and grade. Add your sizes to a quote request and our team confirms lead time and pricing within one business day.
Cut to exact length
Any length from 1 to 15 m — no offcut waste on site
Material options
Uncoated S355JR high-strength cold-rolled strip. Paint or hot-dip galvanize after forming when corrosion protection is required.
In-line punching
Mounting holes and slots punched to your drawing during roll forming
Certified quality
Produced to EN 10162; EN 10204 3.1 mill certificates available
Similar Sizes
Explore alternative dimensions that might suit your needs