Profile Section

280x90x3.5mm S235JR Uncoated Steel C Profile

The 280x90x3.5mm steel C profile is a cold roll-formed lipped channel to EN 10162 with a 280 mm web, 90 mm flanges, 30 mm stiffening edge lips and 3.5 mm sheet thickness, weighing a nominal 14.29 kg/m. Produced to order in uncoated S235JR steel, it is the standard section for solar PV mounting structures, roof purlins and side rails, and light-gauge steel framing — supplied cut to your exact length with no waste on site. This variant is uncoated cold-rolled structural strip in grade S235JR (EN 10025), minimum yield about 235 MPa. The surface is bare — specify shop painting or hot-dip galvanizing in the quote when the profile will be used outdoors.

Select Size

Select Grade

Made to Order — Roll Formed

This profile is roll-formed to order in your exact length (1–15 m; longer on project basis). Minimum production run is approx. 3000 kg per size and grade. Add your sizes to a quote request and our team confirms lead time and pricing within one business day.

Add to Quote Request

Select length and quantity to add to your quote cart

Select Length

Quantity (pieces)

Minimum order: 18 pieces

Minimum total length: 210 m

Weight per meter:14.287 kg/m

Total length:12 meters

Total weight:171.444 kg

Production options

Optional made-to-order requirements — added to this line for our production team.

Pre-painted finish (RAL)Punching / holes to drawingMill certificate EN 10204 3.1

Send your list Contact sales

Applications & Usage

C 280x90x3.5 is typically specified for solar PV piles, rails and bracing on fixed-tilt and tracker structures, roof purlins and wall side rails on industrial buildings, mezzanine joists, and light-gauge steel (LGS) wall and floor framing. Mounting holes and slots are punched in-line to your drawing, and the section pairs with standard smart-screw or bolted connections for fast assembly. S235JR is the general structural grade for indoor frames, painted purlins, and profiles that will be hot-dip galvanized after roll forming. At a nominal 14.29 kg/m and cut-to-length production from 1 to 15 m, material usage is optimized with no offcuts on site. Minimum production run is approximately 3000 kg per size and grade — add your sizes to a quote request and our team confirms exact tonnage, lead time and delivered pricing.

Technical Specifications

Specification	Value
Dimensions	280mm × 90mm × 3.5mm
Weight per Meter	14.287 kg/m
Material	Steel
Alloy/Grade	S235JR
Standard	EN 10162 / EN 10346
Profile Type	C (lipped channel)
Edge Lip (c)	30 mm
Developed Width	≈ 520 mm
Cross-Section Area	≈ 18.20 cm²
Moment of Inertia Iₓ	≈ 2204.8 cm⁴
Moment of Inertia Iᵧ	≈ 217.5 cm⁴
Section Modulus Wₑₗ,ₓ	≈ 155.54 cm³
Section Modulus Wₑₗ,ᵧ	≈ 33.07 cm³
Minimum Production Run	3 t
Finish	S235JR Uncoated
Available Lengths	6m, 12m
Standard Length	6 m
Minimum Order Length	210 m
Cut-to-Length Range	1000 – 15000 mm

Indicative elastic section properties computed from the nominal centerline (thin-walled, corner radii ignored). For preliminary sizing only — not a substitute for a stamped structural calculation.

Indicative load span (single span, simply supported)

Allowable uniformly-distributed load (kN/m) limited by elastic bending about the strong axis (γ = 1.5 on yield, S235JR). Deflection is not checked and usually governs long spans. Indicative only — confirm with a project calculation.